Indian Power Sector: Power Sector Updates

Wednesday, April 6, 2011

Power Sector Updates

How much energy India gulps in a year ? Thats good 450 MTOe. ( 1 MW is equivalentto 2000 TOe).

What is PAT ? That,s Perform Achieve and Trade guidelines issued by BEE for 8 industrial sectors.

How much Wind+Hydro+Biomass can generate in India according to WB? That's 68000 MW.

How much amount India is investing in PV and CSP under NSM ? That's Rs.90,000 Crore.

9900 MW Jaitpur ( MH) NPP is likely to be delayed in wake of Fukushima. This was being executed by Areva od France.

CAG has pulled up which state for losses after reforms.

GAIL is planning to foray into power generation. It is tying up with NTPC to set up gas based plants.

No comments:

Post a Comment

How to construct EHV grid subsatation?

To evacuate power from generating station we need first a Step Up substation since the generation voltage is in the range of 11 KV only. This needs to be stepped up to 400 KV or 220 KV or 132 KV.
Then at the load centres it is again stepped down to 33 KV or 11 KV before final conversion into 440 V.
1.We need suiatble land for subsation.
2.Based upon load growth, operation speed, busbar arrangement, and fauld clearance , the layout and design is prepared.
3. Civil work starts with foundation of structures, equipements and cable trenches. Control room,quarters, fencing, road water supply , drainage and sewerage is contsructed thereafter.
4.Then power transformers, isolators,CTs, PTs, LAs, Control and relay panels, battery chargers abttery sets and shunt capacitors are installed.
5.After planning and laying the control wiring, testing is carried out.
Structures:- ( 220 KV ) all Black steel/ GI
AT1, AT8 for Column
AB 1, AB2 for Beam
AO, AO1 for isolators.
AO3 for CT/PT
AO4 for LA.
Busbars:-
ACSR conductors or pipes strung by tension disc insulators at the ends having tension of 750 kg. They are protected by earth wire at an angle of 30.
Various arrangements of busbars are given in the pictures below.
Earthing:-
Depending upon earth resistivity mesh isdesigned and layed. 200 mm MS rod or 50x10mm MS flat is trenched in 300 mm deep trenches. Mesh is connected to the ground with 28mm dia 3 m long earth electrode. Transformer tanks and neutarl needs separate earth electrodes. Final earth resistance should be < 0.2 ohms.
Safe IR :-
33 KV ( 1000), 132 KV ( 1400 ), 220 KV ( 6000 ).

Small Note on Acounting and Finance

While given a problem of preparing Profit & Loss Account and Balance Sheet from Trial Balance , follwoing tips were given by a friend:-

P & L Account :- What we have done during the year ? Credit ( in ) and Debit ( out ) is part of it.

Balance Sheet :- What is the statement at the end of year? It has two parts- Liability ( share holder ; which has 3 parts: capital, Reserves and Debt , Long Term Loans and Current Liabilty ; which includes short term debt , debtors and Provisions ) and Assets ( Fixed Assesta and Capital assets ; which includes Base, Liquid investment, receivables and Stock/inventory , NCA which means Long Term Investments Loans and Advances)

Expenses are of 3 types:- Cost of Material, Cost of Labour and Admin or Marketing. Further they can be booked as direct expenses( raw material, labour, wages, rent Maint of P&M ) and indirect expenses ( Directors Remun. , clerk's salary, Insurance, Bldg Maint, Heat & Power, Canteen, Welfare, Motor, Prof Charges, Postage and Telegr., Books and stationary, Packing etc )

Net Sales - expenses = PBDIT / EBITDA

PBDIT - DEP - Int = PBT

Op. Profit = Op. Income - Expenses - Dep.

PBT - taxes = PAT ( it has two parts:- Share Holdera and Reserves )

Sales - ST - Discounts = Net Sales

Now the question is , which part of Trial Balance is to be booked under which head?
Well some go into Trading ( raw material, Labour, Insurances, Sales, Discounts ), Some P&L ( salaries, Bldg Maint, Lab, Canteen, Rent, ST ) , some Balance Sheet ( Capital equity, Creditors, Taxation , P & L Account, Xerox Machine, Motor car) .